diff --git a/doc/driver-model/fs_firmware_loader.txt b/doc/driver-model/fs_firmware_loader.txt
new file mode 100644
index 0000000..290915a
--- /dev/null
+++ b/doc/driver-model/fs_firmware_loader.txt
@@ -0,0 +1,133 @@
+# Copyright (C) 2018 Intel Corporation <www.intel.com>
+#
+# SPDX-License-Identifier:    GPL-2.0
+
+Introduction
+============
+
+This is file system firmware loader for U-Boot framework, which has very close
+to some Linux Firmware API. For the details of Linux Firmware API, you can refer
+to https://01.org/linuxgraphics/gfx-docs/drm/driver-api/firmware/index.html.
+
+File system firmware loader can be used to load whatever(firmware, image,
+and binary) from the storage device in file system format into target location
+such as memory, then consumer driver such as FPGA driver can program FPGA image
+from the target location into FPGA.
+
+To enable firmware loader, CONFIG_FS_LOADER need to be set at
+<board_name>_defconfig such as "CONFIG_FS_LOADER=y".
+
+Firmware Loader API core features
+---------------------------------
+
+Firmware storage device described in device tree source
+-------------------------------------------------------
+	For passing data like storage device phandle and partition where the
+	firmware loading from to the firmware loader driver, those data could be
+	defined in fs-loader node as shown in below:
+
+	Example for block device:
+	fs_loader0: fs-loader@0 {
+		u-boot,dm-pre-reloc;
+		compatible = "u-boot,fs-loader";
+		phandlepart = <&mmc 1>;
+	};
+
+	<&mmc 1> means block storage device pointer and its partition.
+
+	Above example is a description for block storage, but for UBI storage
+	device, it can be described in FDT as shown in below:
+
+	Example for ubi:
+	fs_loader1: fs-loader@1 {
+		u-boot,dm-pre-reloc;
+		compatible = "u-boot,fs-loader";
+		mtdpart = "UBI",
+		ubivol = "ubi0";
+	};
+
+	Then, firmware_loader property would be set with the path of fs_loader
+	node under /chosen node such as:
+	/{
+		chosen {
+			firmware_loader = &fs_loader0;
+		};
+	};
+
+	However, this driver is also designed to support U-boot environment
+	variables, so all these data from FDT can be overwritten
+	through the U-boot environment variable during run time.
+	For examples:
+	"storage_interface" - Storage interface, it can be "mmc", "usb", "sata"
+						  or "ubi".
+	"fw_dev_part" - Block device number and its partition, it can be "0:1".
+	"fw_ubi_mtdpart" - UBI device mtd partition, it can be "UBI".
+	"fw_ubi_volume" - UBI volume, it can be "ubi0".
+
+	When above environment variables are set, environment values would be
+	used instead of data from FDT.
+	The benefit of this design allows user to change storage attribute data
+	at run time through U-boot console and saving the setting as default
+	environment values in the storage for the next power cycle, so no
+	compilation is required for both driver and FDT.
+
+File system firmware Loader API
+-------------------------------
+
+int request_firmware_into_buf(struct device_platdata *plat,
+				 const char *name,
+				 void *buf, size_t size, u32 offset,
+				 struct firmware **firmwarep)
+--------------------------------------------------------------------
+Load firmware into a previously allocated buffer
+
+Parameters:
+
+1. struct device_platdata *plat
+	Platform data such as storage and partition firmware loading from
+
+2. const char *name
+	name of firmware file
+
+3. void *buf
+	address of buffer to load firmware into
+
+4. size_t size
+	size of buffer
+
+5. u32 offset
+	offset of a file for start reading into buffer
+
+6. struct firmware **firmwarep
+	pointer to firmware image
+
+return:
+	size of total read
+	-ve when error
+
+Description:
+	The firmware is loaded directly into the buffer pointed to by buf and
+	the @firmwarep data member is pointed at buf
+
+Note: Memory would be allocated for firmware image, hence user should
+	  free() *firmwarep and *firmwarep->priv structs after usage of
+	  request_firmware_into_buf(), otherwise it will always leak memory
+	  while subsequent calls of request_firmware_into_buf() with the same
+	  *firmwarep argument. Those arguments can be free through calling API
+	  below release_firmware();
+
+Example of creating firmware loader instance and calling
+request_firmware_into_buf API:
+	if (uclass_get_device(UCLASS_FS_FIRMWARE_LOADER, 0, &dev)) {
+		request_firmware_into_buf(dev->plat, filename, buffer_location,
+					 buffer_size, offset_ofreading, &fw);
+	}
+
+void release_firmware(struct firmware *firmware)
+------------------------------------------------
+Release the resource associated with a firmware image
+
+Parameters:
+
+1. struct firmware *firmware
+	Firmware resource to release